LevelOne Gigabit PoE Injector, 802.3 af/at/bt, 90W

AIR-PWRINJ6=

IGP-0101

561211

AT-POE

UFP-VIEWPORT

The Cisco AIR-PWRINJ6= Power over Ethernet (PoE) Injector increases wireless LAN deployment flexibility of supported Cisco Aironet access points. This PoE injector provides an alternative powering option to local power, inline power-capable multiport switches and multiport power patch panels. It uses wires in an Ethernet cable to supply inline power to an access point.

The LevelOne IGP-0101 is rugged designed 30 Watts, high power Single port industrial POE Injector is equipped with our high efficiency ColdDesign technology to provide 30 Watts power to your security equipment. The ColdDesign technology will not only power up your PD device, also reduce the excessive heat problem to a minimum. It accepts the input voltage from 48~56 VDC to deliver 30Watts power to meet IEEE802.3af/at standard. It is being rigorously tested for your Security, Transportation and Telco application.

Key Features
- PoE ports can support the IEEE 802.3at standard and power up 30W devices
- 1000Mbps full-duplex, 10/100Mbps full/half-duplex, auto-negotiation, auto-MDI/MDIX
- 40°C to 75°C operating temperature range
- Provides DIN-rail, wall or desktop mounting
- IP30 metal case
- Redundant power inputs with Terminal Block

Extend the range of a PoE connection - even in harsh outdoor conditions.

The Intellinet Network Solutions Outdoor Gigabit High-Power PoE+ Extender Repeater (561211) is designed to extend connection distances from a PoE source to an output device up to 100 m (328 ft.) via Cat5e or Cat6 cable. Cover even longer distances by cascading up to five extenders. The PoE+ Extender Repeater does not need an additional power supply, as it draws the power it needs from the PoE input.

Designed for Outdoor Use

With an IP65 rating and a vast operating temperature range of -40 75°C (-40 - 167° F), the Intellinet Network Solutions Outdoor Gigabit High-Power PoE+ Extender Repeater can be deployed in harsh conditions, which sets it apart from its indoor counterpart, the Intellinet Network Solutions PoE+ Extender (560962).

Simple Installation

Simply connect the "PoE In" port with your PoE injector or PoE switch and connect the "PoE Out" with the PoE device that you wish to connect (e.g., a VoIP phone or a PoE network camera). That's it. There is nothing to configure. It simply could not be any easier.

Reduced Wiring Costs

No need to run AC power lines for your wireless access point, network camera or IP phone. Simply connect the PoE Extender to the LAN switch port and use the existing Cat5 cabling to deliver DC power as well as transfer data.

Power over Ethernet 802.3at Compliant

The Intellinet Network Solutions Outdoor Gigabit High-Power PoE+ Extender Repeater supports the IEEE 802.3at protocol. It is designed to forward data at Gigabit speeds and provide up to 25 watts of input power to a connected IEEE 802.3af- or IEEE 802.3at-compliant device. The cable length on both ends can be up to 100 meters (328 ft.), bringing the total distance to 200 m (656 ft.).

Cascading Power

Daisy-chaining multiple PoE extenders increase the transmission distance even farther. Be advised that each added PoE extender draws up to 4 W of usable PD power, and additional power losses will occur as the cable length increases.

The Airtame PoE Adapter lets you power your Airtame 2 through a PoE connection over USB. Together with our Aircord and a PoE-enabled network, you have a 3-in-1 solution that powers your Airtame, connects it to your network, and plugs into your display screen’s HDMI. Airtame offers a Power over Ethernet (PoE) to USB adapter accessory that is used to provide DC 5V and Ethernet connection over USB to the Airtame 2. The Airtame PoE Adapter is a powered device (PD) that receives PoE from power sourcing equipment (PSE) through a shielded RJ45 connector, and both transforms the power to 5V and separates the data onto the USB lines. The accessory provides the benefit of a clean setup. The Airtame PoE Adapter and Airtame 2 Aircord serve three purposes. In addition to supplying Power and Ethernet connection, the single cable connects the Airtame to the HDMI port on your display. System and IT Administrators will prefer this setup as it guarantees the best performance of your Airtame 2, lowers operating costs, is fast to install, and has higher performance reliability.

The UniFi Protect ViewPort allows you to view your UniFi Protect camera feeds on an HDMI display. It uses Power over Ethernet and connects to the local network hosting your cameras and connects via HDMI to a display. The UniFi Protect ViewPort offers 4K video output at 30 frames per second. Protect systems can be viewed in custom high-density camera matrix configurations.

Aironet Power over Ethernet Injector Provides up to 30W, 90-Day Limited Liability Warranty (AIR-PWRINJ6=)

10/100/1000 Mbps RJ-45, 48V~56V VDC, 370 g

Outdoor Gigabit High-Power PoE+ Extender Repeater, IEEE 802.3at/af Power over Ethernet (PoE+/PoE), Extends Range up to 100m, Metal, IP65

PoE Adapter, 5V DC 2A, USB A, RJ-45, 1G LAN, IEEE802.3af/at, 23x40x112 mm

UniFi Protect ViewPort PoE

Cisco

LevelOne

Intellinet

AIRTAME

Ubiquiti